[7 Fixes] RV Lights Not Working on Shore Power
An RV comes first to mind whenever you think of a day out or camping at distant places. Undoubtedly, it’s a convenient option for an outing as you can enjoy the journey and homely environment simultaneously. It comes with a variety of accessories including ceiling lights.
But there are a number of users who face difficulties with the
That’s why we’re here with all the information they need to get out of this situation. If you’re also a victim of this situation, just a few minutes and read the entire article. So, without wasting time let’s get started.
Why the RV Lights Aren’t Working on Shore Power?
You can find so many reasons why your RV lights aren’t working. Such as –
- The battery is defective
- The fuse is blown
- The bulb gets loose
- The bulb is burned out
- Incompatible light
- The circuit breaker is tripped
- There’s a fault with the inverter or converter
But when it comes to shore power, the most possible reason is the circuit breaker is tripped or the fuse is blown. Don’t worry! We’ll suggest fixes for every cause so that there won’t be any chance for the issue’s persistence.
How to Fix the RV Lights While Not Working on Shore Power?
The fixes are relevant to the causes. First of all, try to diagnose the exact cause in your case. Then apply the fix accordingly. Here are all the fixes –
Reset the Circuit Breaker
As tripped circuit breaker is one of the primary suspects causing this issue, let’s talk about it first. Have a look at the circuit breaker panel in your RV. Check if any of the breakers have tripped which means that’s in the off position. If so, reset it by turning it to the on position.
Replace the Fuse
The other primary suspect is a blown fuse. There’s a fuse in the RV’s electrical system that protects the lights. If this fuse is blown, the lights will not work. The fuse box is usually located in a cabinet near the battery. Remove the fuse and visually inspect it. If the wire that runs through the center of the fuse is broken, the fuse is blown and will need to be replaced.
Replace the Battery
There’s a DC battery that starts the engine of the RV and provides power to the lights and other electrical systems while the vehicle is running. If the battery of your RV gets defective, it can’t store the necessary charge even though it’s connected to shore power. In this case, you need to replace it.
Screw the Bulb Firmly
Sometimes the reason can be as simple as the bulb gets loose at the socket. So, you just simply tighten it by screwing it firmly.
Replace the Bulb
Over time, light bulbs tend to burn out and it’s quite normal. If the light bulbs in your RV are burned out, the lights won’t work. So, verify if this is the cause in your case. If so, you’ll need to replace the light bulbs.
Ensure Compatible Light
If your RV lights aren’t compatible with the system, they won’t work even if you connect them to the shore power. Make sure to use bulbs of a suitable type and wattage.
Replace the Inverter or Converter
Sometimes a faulty inverter or converter causes this issue. If it gets defective then it can’t receive electricity from the power source, in this case, shore power. If you find the inverter or converter is faulty, replace it with a new one.
Frequently Asked Questions and Answers (FAQs)
Why is there no power when I plug into shore power?
Check for the 110-volt outlets. When there’s no power flow toward them, you should check the breakers, especially the GFCI (ground-fault circuit interrupter) breakers. Pay attention to the power pedestal if they’re all in the on position. You can’t test and reset if the GFCI outlets and breakers don’t have the applicable power.
Can an RV run on shore power without a battery?
Truth to tell, a battery isn’t mandatory to use any of the things on your RV DC system. Rather an RV converter will continue to work without battery requirement as long as the vehicle is plugged into shore power.
What voltage is shore power on RV?
In general, an RV can be powered in two ways. One is by its 12-volt battery system. And the other one is by being plugged into a 120-volt power source through an RV power cord, which is shore power.
Conclusion
As you’ve read this far, we hope you’ve understood the entire matter about your RV lights’ inability with the shore power. To conclude, look for the cause and apply the fix regarding it. Some of them require your participation, while most of them require outer help. So, do the needful things to resolve this issue. Let us know which cause is to blame in your case and whether you overcome the problem.
